Table 5 System Event Code Table

Kholer Decision Maker 550 Modbus Register Map / Point List

 

Table 5: System Event Code Table

Code Description
0 Emergency Stop
1 Overspeed
2 Overcrank
3 High Coolant Temperature Shutdown
4 Oil Pressure Shutdown
5 Low Coolant Temperature
6 Low Fuel
7 High Coolant Temperature Warning
8 Oil Pressure Warning
9 Master Not In Auto
10 NFPA 110 Fault
11 Low Battery Voltage
12 High Battery Voltage
13 Battery Charger Fault
14 System Ready
15 Loss of ECM Comm
16 No Oil Pressure Signal
17 High Oil Temperature Shutdown
18 No Coolant Temperature Signal
19 Low Coolant Level
20 Speed Sensor Fault
21 Locked Rotor
22 Master Switch Error
23 Master Switch Open
24 Master Switch Off
25 AC Sensing Loss
26 Over Voltage
27 Under Voltage
28 Weak Battery
29 Over Frequency
30 Under Frequency
31 Load Shed kW Overload
32 Load Shed kW Under Frequency
33 Over Current
34 EPS Supplying Load
35 Internal Fault
36 Engine Cooldown Delay
37 Engine Start Delay
38 Starting Aid
39 Generator Running
40 Air Damper Control
41 Ground Fault
42 EEPROM Write Failure
43 Critical Overvoltage
44 Alternator Protect Shutdown
45 Air Damper Indicator
46 Digital Input 01
47 Digital Input 02
48 Digital Input 03
49 Digital Input 04
50 Digital Input 05
51 Digital Input 06
52 Digital Input 07
53 Digital Input 08
54 Digital Input 09
55 Digital Input 10
56 Digital Input 11
57 Digital Input 12
58 Digital Input 13
59 Digital Input 14
60 Digital Input 15
61 Digital Input 16
62 Digital Input 17
63 Digital Input 18
64 Digital Input 19
65 Digital Input 20
66 Digital Input 21
67 Analog Input 01
68 Analog Input 02
69 Analog Input 03
70 Analog Input 04
71 Analog Input 05
72 Analog Input 06
73 Analog Input 07
74 Reserved for additional input
75 Reserved for additional input
76 Reserved for additional input
77 Reserved for additional input
78 Reserved for additional input
79 Reserved for additional input
80 Reserved for additional input
81 Reserved for additional input
82 Defined Common Fault
83 Software Controlled RDO#1
84 Software Controlled RDO#2
85 Software Controlled RDO#3
86 Software Controlled RDO#4
99 Genset Parameter Warning
100 Genset S/N Mismatch Warning
101 Genset S/N Mismatch Shutdown
103 Protective Relay Overvoltage
104 Protective Relay Under Voltage
105 Protective Relay Overfrequency
106 Protective Relay Underfrequency
107 Protective Relay Reverse Power
108 Protective Relay Over Power
109 Protective Relay Loss of Field
110 Protective Relay Overcurrent Vr
111 Reverse Power Shutdown
112 Over Power Shutdown
113 Loss of Field Shutdown
114 Over Current Shutdown
115 Common Protective Relay Output
116 In Synch
117 Breaker Trip
118 Fuel Valve Relay
119 Pre Lube Relay
120 Air -Fuel Module Start
121 Oil Temperature Loss of Signal
122 High Oil Temperature Warning
123 Intake Air Temperature Loss of Signal
124 High Intake Air Temperature Warning
125 High Intake Air Temperature Shutdown
126 MDEC/ADEC Yellow Alarm
127 MDEC/ADEC Red Alarm
128 MDEC/ADEC Block Heater Control
129 Low Coolant Temperature Shutdown
130 MDEC/ADEC Load Shed Over Temperature
131 Reserved For Future Use
191 Air -Fuel Module Start
192 – 255 Reserved For Future Use

 

See:

Table 1: Register Map Guide

Table 2: Modbus Registers

Table 3: Remapped Registers

Table 4: System Event Codes